View LA5744MP_4381139.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Ordering number : ENA0587A
Monolithic Linear IC
LA5744MP
Overview
Separately-Excited Step-Down
Switching Regulator (Variable Type)
The LA5744MP is a separately-excited step-down switching regulator (variable type).
Functions
* High efficiency. * Time-base generator (300kHz) incorporated. * Current limiter incorporated. * Thermal shutdown circuit incorporated. * Soft start circuit incorporated.
Specifications
Maximum Ratings at Ta = 25C
Parameter Input voltage Maximum output current SW pin application reverse voltage Allowable power dissipation Operating temperature Storage temperature * Specified circuit board : 76.1x114.3x1.6mm3 Symbol VIN IO max VSW Pd max Topr Tstg : Copper foil ratio 60% FR4 Mounted on a circuit board.* Conditions Ratings 30 3 -1 3.9 -30 to +125 -40 to +150 Unit V A V W C C
Recommended Operating Conditions at Ta = 25C
Parameter Input voltage range Symbol VIN Conditions Ratings 4.5 to 28 Unit V
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment.
31407 MS PC / 11707 MS PC 20060929-S00007 No.A0587-1/5
LA5744MP
Electrical Characteristics at Ta = 25C, VO = 5V
Parameter Reference voltage Efficiency Switching frequency Line regulation Load regulation Output voltage temperature coefficient Ripple attenuation factor Current limiter operating voltage Thermal shutdown operating temperature Thermal shutdown Hysteresis width * Design target value : No measurement made. TSD Designed target value. * 15 C RREJ IS TSD f = 100 to 120Hz VIN = 15V Designed target value. * 3.1 165 45 dB A C Symbol VOS f VOLINE VOLOAD VO/Ta Conditions min VIN = 15V, IO = 1.0A VIN = 15V, IO = 1.0A VIN = 15V, IO = 1.0A VIN = 8 to 20V, IO = 1.0A VIN = 20V, IO = 0.5 to 1.5A Designed target value. * 240 1.20 Ratings typ 1.23 83 300 40 10 0.5 360 100 30 max 1.26 V % kHz mV mV mV/C Unit
Package Dimensions
unit : mm (typ) 3275
4.5
Pd max - Ta
1.2
10.0
4.5 1.3
Allowable power dissipation, Pd max - W
4.0 3.90 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 -30 -20
Specified sbstrate: 76.1x114.3x1.6mm3 Copper foil ratio 60% FR4
(8.8)
9.9
(1.6)
1.7
0.9 0.4
4.5
1.5
0.2 2.7
1
5
SANYO : SMP5
0
20
40
60
80
100
120
140
160
Ambient temperature, Ta - C
MSG06072
Pin Assignment
(1) VIN (2) SWOUT (3) GND (4) VOS (5) SS
No.A0587-2/5
LA5744MP
Block Diagram
VIN 1 Constant current circuit Reg. OCP
2 SWOUT
OSC
Reset
Drive
Comp.
TSD 4 VOS VREF
ON/OFF Comp. 0.4V 5 SS 3
Amp.
GND
Application Circuit Example
L1 22H
VIN
SWOUT
LA5744MP
C1 470F /50V D1 SBD C2 390F
VOS SS
C3 1F
GND
R2 R1
Notes : 1. C3 is for the soft start function. Delete C3 and keep the SS pin open when the soft start function is not necessary. 2. In some cases, the output may not turn on if power is applied when a load is connected. If this is a problem, increase the value of
the inductor.
No.A0587-3/5
LA5744MP
Protection Circuit Functional Descriptions 1. Overcurrent protection function The overcurrent protection function detects, on a cycle-by-cycle basis, the output transistor current and turns off that output transistor current if it exceeds 3.1A.
Limit current Inductor current
SWOUT voltage
2. Short circuit protection function This IC prevents the current from increasing when the outputs are shorted by setting the switching frequency to 30kHz if the VOS pin voltage falls below 0.8V. Note 3 : If the soft start function is not used, the IC will start up with the overcurrent protection function operating. At this time, the switching frequency will be cut in half. This means that the switching frequency will be 15kHz at startup. Note 4 : Since the switching frequency becomes 30kHz when the VOS pin voltage falls under 0.8V, the current capacity is reduced. If a load is applied with the VOS pin voltage over 0.8V, the inductance value operates at 22H. If a load is to be applied when this voltage is under 0.8V, the inductance value must be increased.
Description of Functional Settings 1. Calculation equation to set the output voltage This IC controls the switching output so that the VOS pin voltage becomes 1.23V (typ). The equation to set the output voltage is as follows :
R2 VO = 1+ x 1.23V(typ) R1
The VOS pin has the inrush current of 1A (typ). Therefore, the error becomes larger when R1 and R2 resistance values are large. 2. Startup Delay Function The output voltage rises when the internal voltage reaches 0.4V (typical). Until that point, a capacitor is charged from an internal 10A (typical) constant-current supply. The startup delay time can be calculated as shown below Example : Assume a 1F capacitor is used.
Td = C x V 1F x 0.4 = = 40 ms i 10A
No.A0587-4/5
LA5744MP
Timing Chart
VIN voltage
30kHz
300kHz
SWOUT voltage 1.23V 0.8V VOS voltage 0V Td
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above.
This catalog provides information as of March, 2007. Specifications and information herein are subject to change without notice. PS No.A0587-5/5

▲Up To Search▲

Price & Availability of LA5744MP

	To Download LA5744MP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .